ROTATING EQUIPMENT / BEARINGS AND SHAFTS

RotaCore: bearing and shaft engineering studio

From machine loads to a complete bearing report.

RotaCore takes an engineer from the machine to each bearing position. Each step feeds the next, and every result shows its formula, inputs and source, and is marked calculated, provisional or not available. Nothing is assumed silently.

Android · Google Play In testing. The link will appear here when the app is published.

RotaCore home screen showing the eight-step calculation chain from load to clearance class
The calculation chain: each step feeds the next.
8steps in the calculation chain
2bearings of a shaft in one report
EN / हिंदीinterface
Localnothing is uploaded

Why RotaCore

A bearing problem on site rarely needs one formula. It needs the load on each bearing, the life at that load, a check that the lubricant film is thick enough, the right clearance after mounting, and a greasing interval and quantity the crew can follow. These numbers usually come from different catalogue pages, spreadsheets and memory, and the assumptions between them get lost.

RotaCore keeps them in one chain. The load you enter for the shaft is the load used for the life, the static check, the lubrication and the greasing. Every value shows where it came from, and anything the app cannot support with data is marked provisional or not available instead of being filled with a guess. OEM data you enter is kept side by side with the calculation and never overwritten.

CALCULATION CHAIN / M2 TO M15

The calculation chain

Work through the eight steps for a project, or open any step on its own. New to the method? Read how to calculate bearing L10 life, with a worked example.

SELECTION AND DIAGNOSTIC TOOLS

Selection and diagnostic tools

Machine report: both bearings of a shaft together

Version 3 adds the Machine Report. You describe the machine once in eight tabs (machine, bearings, loads, operating, environment, lubrication, documents, review), and RotaCore calculates both bearing positions of the shaft together. Loads with their position and direction, including overhung pulleys and impellers, are split to both bearings.

Each bearing gets its own life, static safety factor, viscosity ratio, relubrication interval and grease quantities, with the clearance after mounting and the drive-up for tapered bores. The review lists conflicts with OEM data, missing data and every provisional value with the reason.

RotaCore Machine Report review tab for the 22216 EK conveyor pulley worked example, showing loads, L10h, s0, kappa and relubrication interval for the drive and non-drive side
Review tab of the built-in 22216 EK conveyor pulley worked example. Example data, not a plant record.

Results can be shared as a one-page results poster or a PDF engineering report for approval.

Current status and limits

The web preview runs version 3 in the browser with a sample project and a reduced bearing list; nothing is uploaded. Version 3 is still being tested on real plant equipment. An Android app is in testing for Google Play.

Results are engineering aids to be checked against the bearing maker's current data. A competent engineer must review them before any equipment decision. RotaCore is an independent tool by MaintAi_Lab and is not affiliated with any bearing manufacturer.

RotaCore privacy policy ↗ · Website privacy · RotaCore on the tools page

STANDARDS / MECHATLAS

Standards behind the work

RotaCore calculations build on these published methods. Check the edition you work to: MechAtlas, also by MaintAi_Lab, shows each standard's current edition, whether it is being revised or replaced, and what to use instead.

All bearing standards in MechAtlas ↗

Frequently asked questions

Do I need to install anything?

No. The web preview runs in a normal browser on a PC, tablet or phone. An Android app is in testing.

Is my data uploaded?

No. In the web preview, calculations run in your browser and nothing is uploaded. Use the app's backup to keep a copy of your projects.

Which bearings are included?

The web preview uses a reduced bearing list. You can add your own bearings to the bearing database.

Does RotaCore replace the bearing maker's calculation?

No. It shows its formulas, inputs and sources so you can check them, and marks values it cannot support as provisional. Confirm critical results with the bearing maker's current data.

Is there a Hindi version?

Yes. The interface can be switched between English and Hindi.

Start with your next bearing

Open the web preview and load the built-in conveyor pulley example to see a full report.